Jump to content

Dry-ice blasting

From Wikipedia, the free encyclopedia
(Redirected from Dry ice blasting)

Dry-ice blasting used to clean a rubber mold

Dry-ice blasting is a form of carbon dioxide cleaning, where dry ice, the solid form of carbon dioxide, is accelerated in a pressurized air stream and directed at a surface in order to clean it.[1][2]

The method is similar to other forms of media blasting such as sand blasting, plastic bead blasting, or sodablasting in that it cleans surfaces using a medium accelerated in a pressurized air stream, but dry-ice blasting uses dry ice as the blasting medium. Dry-ice blasting is nonabrasive, non-conductive, nonflammable, and non-toxic.

Dry-ice blasting is an efficient[3][verification needed] cleaning method. Dry ice is made of reclaimed carbon dioxide that is produced from other industrial processes, and is an approved media by the EPA, FDA and USDA. It also reduces or eliminates employee exposure to the use of chemical cleaning agents.

Compared to other media blasting methods, dry-ice blasting does not create secondary waste or chemical residues as dry ice sublimates, or converts back to a gaseous state, when it hits the surface that is being cleaned. Dry-ice blasting does not require clean-up of a blasting medium.[4] The waste products, which includes just the dislodged media, can be swept up, vacuumed or washed away depending on the containment.

Method

[edit]
Dry-ice blasting illustration

Dry-ice blasting involves propelling pellets at extremely high speeds. The actual dry ice pellets are quite soft, and much less dense than other media used in blast-cleaning (i.e. sand or plastic pellets). Upon impact, the pellet sublimates almost immediately, transferring minimal kinetic energy to the surface on impact and producing minimal abrasion. The sublimation process absorbs a large volume of heat from the surface, producing shear stresses due to thermal shock.[5] This is assumed[by whom?] to improve cleaning as the top layer of dirt or contaminant is expected to transfer more heat than the underlying substrate and flake off more easily. The efficiency and effectiveness of this process depends on the thermal conductivity of the substrate and contaminant. The rapid change in state from solid to gas also causes microscopic shock waves, which are also thought to assist in removing the contaminant.[citation needed]

Equipment

[edit]

The dry ice used can be in solid pellet form or shaved from a larger block of ice. The shaved ice block produces a less dense ice medium and is more delicate than the solid pellet system. In addition, pellets may be made by either compressing dry ice snow, or using tanks of liquid CO2 to form solid pellets.[6] Dry ice made with compressed snow breaks apart more easily and is not as aggressive for cleaning.

Dry-ice blasting technology can trace its roots to conventional abrasive blasting. The differences between an abrasive-blasting machine and a dry-ice blasting machine are in how they handle the blast media. Unlike sand or other media, dry ice is generally used at its sublimation temperature. Other differences include systems for preventing the ice from forming snowball-like jams, and different materials to allow operation at very low temperatures.

There are two methods of dry-ice blasting, two-hose and single hose. The single hose system is more aggressive for cleaning, since the particles are accelerated to faster speeds.

Two-hose dry-ice blasting was developed before the single-hose system. The two-hose dry-ice blasting approach is very similar to a suction-feed abrasive blast system. Compressed air is delivered in one hose, and ice pellets are sucked out of a second hose by the venturi effect. Compared to a single-hose system, the two-hose system delivers ice particles less forcefully (approximately 5% for a given air supply). For a given amount of compressed air, two-hose systems can have less vertical distance between the machine and applicator. For most systems available today this limit is well in excess of 7.5 m (25 feet). Two-hose systems are generally cheaper to produce due to a simpler delivery system. These systems are rarely seen today as they are less efficient in most applications. Their principal advantage is in allowing finer particles of ice to be delivered to the applicator as the late combination of warm air with cold ice results in less sublimation in the hose. These systems allow for more delicate surfaces to be cleaned such as semiconductors.[citation needed]

The first dry-ice blasting machine to be commercialized was a single-hose system. It was developed by Cold Jet, LLC in 1986,[7][8] and uses a single hose to deliver air blasts and dry ice. Single-hose dry-ice blasters share many of the advantages of single-hose abrasive-blast systems. To avoid the potential dangers of a pressurized hopper, single-hose dry-ice blasters make use of a quickly cycling airlock. The single-hose system can use a longer hose than its double-hose counterpart without a significant drop in pressure when the ice leaves the hose. The additional power comes at the cost of increased complexity. Single-hose systems are used where more aggressive cleaning is an advantage. This allows heavier build-up to be cleaned and allows moderate buildup to be cleaned faster.

In 2014, a Slovakian company, ICS Ice Cleaning Systems, patented a set of crushing rollers to reduce the size of particles leaving the applicator gun. This allowed the operator for the first time to control the fractional size of each dry ice pellet. From the International standard 3mm to 1.5mm and smaller if desired. Simply by the push of an electronic button. Allowing for applications on more delicate surfaces without harming them.

Additionally, one could shoot these smaller fractions of dry ice pellets towards multiple surfaces with varying coatings, compositions, and textures, while mitigating risks of damaged surfaces. While attempted previously with nozzle fragmentation devices, these new crushing rollers provided accuracy and efficiency not previously achieved. In 2020, a Florida-based entrepreneur and founder of the DryceNation community, began sharing this method which was immediately well received by the collector car industry. Videos on social media platforms further accelerated this process which was widely accepted by 2022.

Uses

[edit]
Dry-ice blasting used to clean bakery equipment

Dry-ice blasting is utilized in many different types of industries. The unique properties of dry ice make it an ideal cleaning solution in many commercial and manufacturing settings.

Dry-ice blasting can clean numerous objects with differing, complex geometries at once, which is why cleaning plastic and rubber molds is a main application for the technology.[9] Dry ice replaces traditional cleaning methods that rely on manual scrubbing and the use of chemical cleaning agents. Dry-ice blasting cleans the molds in-place at operating temperature, which eliminates the need to shut production down for cleaning.[10]

Food processing industry

[edit]

Dry-ice blasting can be used to clean food processing equipment.[11] As early as 2004, the UK Food Standards Agency documented the process to effectively decontaminate surfaces of Salmonella enteritidis, E. coli, and Listeria monocytogenes such that these microorganisms are not detectable using conventional microbiological methods.[12] "As a result of two outbreaks salmonellosis associated with the consumption of peanut butter and baby food in 2006–2007,[13][14] an effort was taken" by GMA members such as Cargill "to reassess industry practices for eliminating salmonella in low-moisture products" because "Salmonella outbreaks from low-moisture products are relatively rare but often impact large numbers of people." A document resulted from this effort describing a variety of waterless cleaning methods,[15] including dry-ice blasting.

It may also be used to clean some equipment without disassembly and without producing fire or electrical hazards. The EPA recommends dry-ice blasting as an alternative to many types of solvent-based cleaning.[16]

Disaster remediation

[edit]

The cleaning process may be used for disaster remediation including mold, smoke, fire, and water damage.[17]

Historic item preservation

[edit]

Due to the nonabrasive nature of dry ice and the absence of secondary waste from the cleaning process, dry-ice blasting is used in conservation and historical preservation projects. The cleaning process was used in the conservation of the USS Monitor[18] and the Philadelphia Museum of Art.[19]

Semiconductor fabrication

[edit]

Due to the blast media sublimating without residue, dry-ice blasting finds use in the semiconductor, aerospace, and medical device manufacturing[20] industries.

Metalworking

[edit]

The cleaning process is also used in other manufacturing settings, such as cleaning production equipment on automated weld lines,[21] cleaning composite tooling,[22] cleaning industrial printing presses,[23] cleaning molds and equipment used in foundries,[24] and to clean equipment and tooling in onshore and offshore environments in the oil and gas industry.

Dry-ice blasting is also used to deburr and deflash parts[25] and in surface preparation prior to painting.

Safety

[edit]

Carbon dioxide is increasingly toxic starting at concentrations above 1%,[26] and can also displace oxygen resulting in asphyxia if equipment is not used in a ventilated area. In addition, because carbon dioxide is heavier than air, exhaust vents are required to be at or near ground level to efficiently remove the gas. At normal pressure dry ice is −78 °C (−108 °F) and must be handled with insulated gloves. Eye and ear protection are required to safely use dry-ice cleaning equipment.

History

[edit]

It is believed the US Navy, in 1945, were the first to experiment with dry-ice blasting. They were interested in using the technology for various degreasing applications.[27]

In 1959, Unilever filed a patent for using dry-ice blasting (or water-ice blasting, or some combination of the two) as a method of removing meat from bone.[28]

In 1971, Chemotronics International Inc. filed a patent for using dry-ice blasting for the purposes of deburring and deflashing.[29]

A patent for dry-ice blasting was filed by Lockheed Martin in 1974.[30]

The first patents regarding development and design of modern-day single-hose dry-ice blasting technology were awarded to David Moore of Cold Jet, LLC in 1986, 1988 (U.S. patent 4,617,064 and U.S. patent 4,744,181).

See also

[edit]

References

[edit]
  1. ^ Máša, Vítězslav; Horňák, David; Petrilák, Dalimil (December 2021). "Industrial use of dry ice blasting in surface cleaning". Journal of Cleaner Production. 329: 129630. Bibcode:2021JCPro.32929630M. doi:10.1016/j.jclepro.2021.129630.
  2. ^ Kohli, Rajiv (2019). "Applications of Solid Carbon Dioxide (Dry Ice) Pellet Blasting for Removal of Surface Contaminants". Developments in Surface Contamination and Cleaning: Applications of Cleaning Techniques. pp. 117–169. doi:10.1016/B978-0-12-815577-6.00004-9. ISBN 978-0-12-815577-6.
  3. ^ Jet, Cold. "Dry Ice Blasting and Dry Ice Production Equipment by Cold Jet". coldjet.com. Retrieved 10 July 2018.
  4. ^ "Apex Dry Ice Blasting: Industrial Services – Akron, Ohio". apexdryiceblasting.com. Retrieved 11 July 2018.
  5. ^ How CO2 Blasting Works
  6. ^ "High Density CO2". Retrieved 18 July 2018.
  7. ^ "Moore, David E., US patents#4,617,064 and #4,744,181". Archived from the original on 28 April 2019. Retrieved 12 July 2007.
  8. ^ Jet, Cold. "Dry Ice Blasting and Dry Ice Production Equipment by Cold Jet". coldjet.com. Retrieved 10 July 2018.
  9. ^ Callari, Jim. "Dry-Ice Cleaning Pays Off Big For High-Tech Molder". ptonline.com. Retrieved 10 July 2018.
  10. ^ Jet, Cold. "Dry Ice Blasting and Dry Ice Production Equipment by Cold Jet". coldjet.com. Retrieved 10 July 2018.
  11. ^ "Case Study: Bakery Implements Dry Ice Cleaning". Food Manufacturing. 15 June 2017. Retrieved 22 December 2023.
  12. ^ Millar, Ian (19 September 2004). Cold Jet – A novel technique for cleaning and decontaminating food processing areas, equipment, carcasses and foods (PDF) (Technical Report to the Food Standards Agency). Stonehaven, Aberdeenshire, Scotland: Microchem Bioscience Limited.
  13. ^ "Multistate Outbreak of Salmonella Tennessee Infections Linked to Peanut Butter (FINAL UPDATE)". CDC. U.S. Department of Health & Human Services. 7 March 2007.
  14. ^ Sotir, Mark J.; Ewald, Gwen; Kimura, Akiko C.; Higa, Jeffrey I.; Sheth, Anandi; Troppy, Scott; Meyer, Stephanie; Hoekstra, R Michael; Austin, Jana; Archer, John; Spayne, Mary; Daly, Elizabeth R.; Griffin, Patricia M.; Salmonella Wandsworth Outbreak Investigation, Team (December 2009). "Outbreak of Salmonella Wandsworth and Typhimurium Infections in Infants and Toddlers Traced to a Commercial Vegetable-Coated Snack Food". Pediatric Infectious Disease Journal. 28 (12): 1041–1046. doi:10.1097/INF.0b013e3181af6218. PMID 19779390. Very minor formatting correction at "Outbreak of Salmonella Wandsworth and Typhimurium Infections in Infants and Toddlers Traced to a Commercial Vegetable-Coated Snack Food: ERRATUM". The Pediatric Infectious Disease Journal. 29 (3): 284. March 2010. doi:10.1097/01.inf.0000369241.58743.90. [T]he first subheading in the Results section was incorrect. The subheading should have appeared as Salmonella Wandsworth. (The original had "Salmonella wandsworth".)
  15. ^ Control of Salmonella in Low-Moisture Foods (PDF). Grocery Manufacturers Association. 4 February 2009.
  16. ^ 1,1,1-Trichloroethane (TCA) Hazards and Alternatives (PDF) (Technical Fact Sheet). United States Environmental Protection Agency. October 2000. EPA 905-F-00-026.
  17. ^ "Applications | Go Green – Dry Ice Blasting". gogreendryiceblasting.com. Archived from the original on 10 July 2018. Retrieved 10 July 2018.
  18. ^ Erickson, Mark St. John. "Speeding up the Monitor rescue". dailypress.com. Archived from the original on 11 July 2018. Retrieved 10 July 2018.
  19. ^ "Preserving a treasure chest". Philly.com. Retrieved 10 July 2018.
  20. ^ "Dry Ice Cleaning in Medical Device Manufacturing". Medical Design Technology. 11 May 2017. Retrieved 10 July 2018.
  21. ^ "Cleaning automated weld lines with dry ice". Retrieved 11 July 2018.
  22. ^ Sloan, Jeff. "Yes, you clean tooling board with dry ice". compositesworld.com. Retrieved 11 July 2018.
  23. ^ "Clean Printing Presses, Rollers, & Ink Trays with Dry Ice Blasting". continentalcarbonic.com. Retrieved 11 July 2018.
  24. ^ Jet, Cold. "Dry Ice Blasting and Dry Ice Production Equipment by Cold Jet". coldjet.com. Retrieved 11 July 2018.
  25. ^ "How dry ice can assist medical device manufacturers | Medical Design and Outsourcing". medicaldesignandoutsourcing.com. 3 April 2017. Retrieved 10 July 2018.
  26. ^ Friedman, Daniel. "Toxicity of Carbon Dioxide Gas Exposure, CO2 Poisoning Symptoms, Carbon Dioxide Exposure Limits, and Links to Toxic Gas Testing Procedures". InspectAPedia. Archived from the original on 28 September 2009. Retrieved 9 March 2011.
  27. ^ Foster, Robert W. "Carbon Dioxide (Dry-Ice) Blasting" (PDF). old.coldjet.com. Archived from the original (PDF) on 6 March 2007. Retrieved 24 September 2018.
  28. ^ Method of removing meat from bone, 21 January 1960, retrieved 24 September 2018
  29. ^ Method for the removal of unwanted portions of an article by spraying with high velocity dry ice particles, 12 July 1971, retrieved 24 September 2018
  30. ^ "Lockheed Martin Dry Ice Blasting Patent US4038786A". Retrieved 18 July 2018.
[edit]